Mengapa Flextreme

Why Buy Flextreme ? /Mengapa Beli Flextreme

Mengapa Beli Flextreme

Semua Produk Flextreme dipastikan sudah melewati Quality Control
Garansi 1 (Satu) Tahun Penuh - One to One Replacement
Keunggulan Produk Kami:

- Satu-satu nya merk media converter paling lengkap (Single Core, SFP Media Converter, Converter Multimode - Singlemode, Kecepatan 100 Mbps maupun 1000 Mbps)
- Satu-satu nya Media Converter Gigabit dengan harga kompetitive yang support koneksi UTP 10/100/1000 Mbps
- Satu-satu nya merk Media Converter Single Core yang mempunyai pilihan 100 Mbps atau 1000 Mbps
- Satu-satu nya Media Converter dengan paket Pair (2 Unit) Single Core, jadi harga lebih kompetitive
- SFP module nya kompatible dengan merk lain
- Pilihan Jarak untuk SFP Module Single Mode (40 Km, 80 Km)
- Chassis Rackmount dengan 2 unit power supply redundant, bukan optional

Mengapa bestpricekomputer ???

Produk dijamin asli dan bergaransi resmi

bestpricekomputer hanya menyediakan produk-produk terbaru yang asli dan bergaransi resmi dari distributor resmi pemegang merek di Indonesia. Setiap produk yang kami tawarkan sudah melewati proses quality control oleh tim internal kami.

Harga terbaik disertai segudang diskon dan promo

Kami selalu ingin memberikan kepuasan lebih bagi setiap customer. bestpricekomputer berkomitmen untuk memberikan harga terbaik dan menghadirkan berbagai program diskon dan promo.

Stok Selalu Tersedia

Kami tidak ingin membuat customer menunggu. bestpricekomputer memastikan setiap produk yang kami tawarkan selalu siap untuk diantarkan kepada customer.

Layanan antar cepat dan selalu tepat waktu

Kami menyadari pentingnya layanan yang cepat bagi setiap customer, untuk itu kami memiliki tim delivery profesional yang selalu siap mengantarkan produk dengan cepat dan tepat waktu.

Customer Support yang handal

Layanan yang terbaik kepada customer adalah yang terpenting bagi kami. Tim Customer Supportbestpricekomputer berdedikasi penuh untuk melayani setiap kebutuhan customer kami dengan ramah dan sigap.

FL-10GSFP-LR SFP Module 10G Single Mode, 1310nm, 10 Km

FL-10GSFP-LR SFP Module 10G Single Mode, 1310nm, 10 Km
Harga : Rp 25,000,000

Application
Rack to rack
Premise
metro
Data Centers
Switches and Routers

FEATURE:
10Gb/s serial optical interface compliant to 802.3ae 10GBASE-SR/LR/ER
Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module “SFP+”
DFB transmitter, PIN photo-detector
2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers
Operating case temperature: 0 to 70°C
All-metal housing for superior EMI erformance
Low power consumption
Advanced firmware allow customer system encryption information to be stored in transceiver
Cost effective SFP+ solution, enables higher port densities and greater bandwidth
RoHS compliant

Model No.	Data Rate	Wavelength/ Light Source	Media Type	Reach	TX Power (dBm)	RX Sens. (dBm)	Temp. ( o C)
FL-10GSFP-SR	10G	850nm	MMF	300m	-3	-9.9	0~70
FL-10GSFP-LR	10G	1310nm	SMF	10km
FL-10GSFP-LRM	10G	1310nm	MMF	220m	-2	-6.5	0~70
FL-10GSFP-LH	10G	1310nm	SMF	20km
FL-10GSFP-ER	10G	1550nm	SMF	40km	0	-15.8	0~70
FL-10GSFP-ZR	10G	1550nm	SMF	80km

Flextreme FL-10GSFP-SR SFP Module 10G Multi Mode, 850nm, 300 Meter

Jual Flextreme FL-10GSFP-SR SFP Module 10G Multi Mode, 850nm, 300 Meter

Harga : Rp 11,000,000
Description
The SFP+ module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector.
The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-SR/LR/ER standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 kΩ. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 kΩ to 10 kΩ resistor
The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 kΩ, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.
Application
Rack to rack
Premise
metro
Data Centers
Switches and Routers

FEATURE:
10Gb/s serial optical interface compliant to 802.3ae 10GBASE-SR/LR/ER
Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module “SFP+”
DFB transmitter, PIN photo-detector
2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers
Operating case temperature: 0 to 70°C
All-metal housing for superior EMI erformance
Low power consumption
Advanced firmware allow customer system encryption information to be stored in transceiver
Cost effective SFP+ solution, enables higher port densities and greater bandwidth
RoHS compliant

Model No.	Data Rate	Wavelength/ Light Source	Media Type	Reach	TX Power (dBm)	RX Sens. (dBm)	Temp. ( o C)
FL-10GSFP-SR	10G	850nm	MMF	300m	-3	-9.9	0~70
FL-10GSFP-LR	10G	1310nm	SMF	10km
FL-10GSFP-LRM	10G	1310nm	MMF	220m	-2	-6.5	0~70
FL-10GSFP-LH	10G	1310nm	SMF	20km
FL-10GSFP-ER	10G	1550nm	SMF	40km	0	-15.8	0~70
FL-10GSFP-ZR	10G	1550nm	SMF	80km

Compatible : Switch CISCO, ZTE, D-Link, TP-LINK, Linksys, Airlive, Edimax, Planet, Allied Telesis, Trendnet, Juniper, HP Procurve, Alcatel Lucent (others brand please contact us)

Flextreme FL-SFP1000SM-120

Flextreme FL-SFP1000SM-120
Harga : 5,700,000

The SFP transceiver supports dual data-rate of 1.25Gbps/1.0625Gbps and up to 120km transmission distance with single-mode fiber 1550nm.
The transceiver consists of two sections: The transmitter section incorporates a FP or DFB laser. the receiver section consists of a PIN photodiode integrated with a trans-impedance preamplifier (TIA).
All modules satisfy class I laser safety requirements. The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault indicates that degradation of the laser. Loss of signal (LOS) output indicates the loss of an input optical signal of receiver.
The standard serial ID information compatible with SFP MSA describes the transceivers capabilities, standard interfaces, manufacturer and other information. The host equipment can access this information via the 2-wire serial bus. For more information, please refer to SFP Multi-Source Agreement (MSA)

FEATURE:
SFP package with LC connector
1550 nm optical transmission with single-mode fiber
Up to 120Km transmission with single-mode fiber
+3.3V single power supply
LVPECL compatible data input/output interface
Low EMI and excellent ESD protection
laser safety standard IEC-60825 compliant
Compatible with CE/RoHS

Support: CISCO Compatible

Flextreme FL-8110GSA-11-20-AS

Jual Flextreme FL-8110GSA-11-20-AS
Harga : Rp 1,800,000

Produk ini mendukung IEEE802.3 10 Base-T standar / IEEE 802.3u 100Base-TX/FX standar / IEEE 802.3z 1000Base-TX/FX standar, serta full duplex dan mode half duplex.

Teknis parameter:
1. Standar Protokol:
IEEE802.3 10 Base-T standar
IEEE 802.3u 100Base-TX/FX standar
IEEE 802.3z standar 1000Base-TX/FX
2.Connector: oneUTPRJ-45connector, oneSC / STconnector
3. Operasi Mode: modus duplex penuh atau setengah modus duplex
4. Power supply parameter:
luar: 5V DC 2A
built-in: 110-265V AC 48VDC
5. Lingkungan Suhu: 0 60 lt; br /> 6??. Kelembaban relatif: 5% -90%
8. TP kabel: CAT5 kabel UTP
9. Mentransfer serat:
multi-mode: 50/125, 62.5/125 atau 100/140μm
single mode :: 8.3/125, 8.7/125, 9/125 atau 10/125μm

FL-8110MA-11-2: Media Converter 10-100 Mbps to 100FX, Multi-Mode 2 Km, SC

FL-8110MA-11-2
FL-8110MA-11-2: Media Converter 10-100 Mbps to 100FX, Multi-Mode 2 Km, SC
Harga : Rp ~~1,950,000~~ -- Rp 895,000

GENERAL DESCRIPTION

The media converter transform the transmission media of Ethernet signal from CAT5 to optical fiber. it can extend the transmission distance to several kilometer or hundred kilometer.
Using media converter is a economical solution to achieve long distance transmission base on current status.

FEATURES

1.Built in a 2-port switch:
--Pass all packets without address and CRC check (optional);
--Supports modified cut-through frame forwarding for low latency;
--Supports pure converter mode data forwarding for extreme low latency;
--Supports flow control for full and halt duplex operation;
--Bandwidth control;
--Forward 1600 bytes packet for management;
--Optional forward fragments.

2. Supports 100Base-FX standard;
3.Built in 128Kb RAM for data buffer;
4.Supports auto MDI-MDIX function;
5. Supports link fault pass through function (LFP);
6. Supports for end fault function (optional);
7. LED display for link/activity, full/half, 10/100M
8. Support EEPROM configuration (optional);
9. the longest transmission distance reach 120 kilometers;

STANDARD

IEEE802.3 ETHERNET STANDARD
IEEE802.3u FAST ETHERNET STANDARD